problem

i bought a D tuner for my warwick and it is always sharp the switch stops on the back of the G tuning key

Hi, I just replaced the strings on my 5-str. Corvette Std. for the first time and have a slight intonation problem. The problem is that the B-string is still too sharp at the 12th fret and I can't turn the intonation screw any more because the spring on the intonation screw seems to be...

I have a Rockbass Streamer that came with normal strap locks. I bought Warwick security strap locks, as they seem the natural choice. The problem is that the stock strap locks were held by 4mm diameter screws, while the security starp locks are provided with 3.5mm diameter screws. So the...

Hello Warwickophiles :) I need your help with serial number of my bass. I search the forum and I know to how read it but there is one problem. My serial is: M25990 and we all know that the letter "M" is 13th so in what month my bass was made. It can't be fake. Thanks for help. Cheers :)...

***HELP*** I'm having some issues with my rockbass 4 string vette standard. I have the 06 model with the ground wire issue which has been fixed but now....The bass and treble controls are acting up. When the bass and treble are center...a lot of static. If I turn up the turn the...

I just bought a 2004 Streamer LX 4 string, and I can't get the strap locks attached. They seem very slightly too big and won't fit in the holes. Any suggestions?

I took the neck off my bass so I could bring it to work and change out the PU's. I can keep the body on my locker. The problem is my PU's are going to be a week late, so the neck will be off my bass for almost 2 weeks. Does it matter? Should I take it home, put it back together until the PU's...

Hi All, This is my first post to the community, which is a question I would apprieciate some feedback on, and I apologise if this has been posted before. I recently purchased a 2nd hand RB Corvette Active 4 string which I am very happy with. It's in almost mint condition, and I have...

Hi there, The Treble knob on my Corvetted $$ is faulty. I've downloaded a wiring diagram, but can't work out the identity of the pot I need to order from your spares shop. Can you help please?

Can i use 125 gauge strings which are normally for 5 string basses on my 4 string corvette for drop c tuning?

Hi! I wondered....Will there be a problem on the JAN II with moving to a lighter string-gauge? On other basses I`ve experienced rattling, since the tracks on the nut have become too wide for slimmer strings. I`ll go from Elixir 45-135 to DR Hi-beams 40-120.

hey guys, Just got my new Warwick gear out of the box, a profet 5.1 and a 411 cab. But I'm having a problem with the head. I followed the initial set up instructions but when i began to turn up the master there was no sound. So after much turning it off and on again I realised that their was...

I own a Warwick $$ corvette and I think that a might have a tiny problem with the pickup electronics :( . I own a peavey TKO 115 bass amp( not the best amp in the world but) the problem is, when I let a note sustain when playing my $$, the sustain has a slight distorted/fuzz sound to it. I have...

Hi, I´m using a 250 Watts Warwick Bass head amplifier. The amplifier has 4 Ohm outputs. I have a 200 Watts 1x15 Cab and a 200 Watts 4x8 Cab connected in parallel. Both Cabs are 8 Ohms and also from Warwick. Bass Guitar is a H&K 4 string active bass. I´m playing this rack for a couple...

Hey Guys, Just played abit with my corvette when i recognized a failure i can't explain to myself. As you know you got 3 different setups for each PU of the $$. Everything worked fine the whole time - but today it seems that one config doesn't work at all. If i blend towards the neck PU...

Hey there, this is my first post here :) I'm having a bit of a problem with my streamer stage one 5 (from 2002 bought second hand)...it suddently started to make an irritating noise whenever I switched to passive but I didn't pay it much atention because I rarelly use it in passive mode...

I've just finished adjusting the truss rod, bridge, saddles and nut on my bass, and now the E-string will barely register and distorts beyond belief when run only on the piezo pickup! Does the string have to sit a specific way on the saddle to make it work or what? And it's not a battery problem...

hallo everybody, when my new 411 nd arrived about 4 month ago, the first thing that happened after pulling it out of the box: the shield in the right corner fell off :roll: well, since that time it never hold longer than 1 or 2 weeks after putting it on again. i tried every glue and so...

hi I'm using my profet 3.2 for nearly a year, without problems, but today something went wrong: I was playing at about half volume (master at 5, gain set properly), and suddenly came a really big "BANG" sound. After it the rig started to buzz. I've checked the speakers (Hartke alus), none of...

I've been changing my JAN II to a III. And I've come up with a bit of a problem.... The angle of the head and the angle of the end of the neck are not 90 degrees - this is fine with the JAN II as it can rotate on top of it's "pins", but the JAN III can't rotate. Here's a picture so that...